Cricut Flowers can be a little tough to assemble. Here are detailed instructions on how to assemble the Cricut Flower Shoppe Daffodil, Tiger Lily, Poppy, and Peony.
Last week, I threw a cozy outdoor Friendsgiving, for which I made a TON of 3D paper poppies on my Cricut Explore. I absolutely love these flowers! They were originally a part of the cricut flower cartridge “Cricut Flower Shoppe,” but now they are also available in the Cricut Design Space individually.
Problem is, these cardstock flowers don’t come with any instructions and some of them can be a little confusing, especially if you’re not the most spatially aware person. So I thought I’d put together a couple tutorials to show you how to assemble some of these flowers.
Thankfully, once you see a few of the tricks that are used to assemble them, it becomes easier to figure out how additional cardstock paper flowers go together, too.
Stop pulling your hair out and start creating confidently with your Cricut! Finally understand how to use your Cricut with my Learn Your Cricut eBooks!
Supplies Needed:
Assembling Cricut Flowers
What Glue do I Use?
For glue, I use quick-dry tacky glue. I tend to be a messy gluer, but because almost all of the gluing is hidden, it doesn’t really matter. You could also use a hot glue gun (be careful!) or something like E6000, though I prefer a glue that dries faster.
Tiger Lily #MA3E15
Let’s start with the tiger lily. This is a good one to start with because it has a couple features that you’ll see over and over in the Cricut flowers. It has three parts — the petals, the pistil/stamen (I remembered something from botany!), and the leaves.
You’ll see on the petals and the leaves a few small tabs. These tabs are meant to be glued. They will help guide you as you assemble the flower. Many of the cardstock flowers have these tabs, and once you figure out how they work, making flowers becomes a lot easier!
Fold the petals of the flowers into sort of a roll. You’ll see the tab then overlaps the other side.
Glue! Do this for both sets of petals and the leaf.
You’ll notice that there are two parts to the leaves, one that is 3D (that you glued) and one that is flat.
Stack and glue. Sometimes I offset them, and sometimes I stack them straight on — if I’m making several, I try and mix it up a bit.
For anything that looks like the pistil/stamen, roll it. I generally use a wooden dowel or pencil to get an even roll. Glue that too.
To assemble, nestle one set of petals in the other. Glue. I like to roll the petals a little around a pen to help them spread out.
Nestle the pistil/stamem inside the petals, and glue. I usually set it upright in a roll of washi tape to allow it to dry straight. Then glue the leaves to the bottom.
Yay! A tiger lily!
Poppy #MA3E13
Let’s do the poppy next. There are no tabs on the petals for the poppy, so they stay flat. I roll the edges up a little using a pen, to give them a bit of a 3D feel. Offset the two petal pieces, and glue.
The pistil/stamen piece may leave you scratching your head, but it’s easy. Fold the taller part in half and then roll starting from that side.
Then glue it to the middle of your poppy.
Make the leaves like you did the tiger lily, and glue below the petals.
Super easy, right? Let’s try the daffodil.
Daffodil
The daffodil has similar petals to the tiger lily, but it also has that extra piece in the center. Glue all the tabs, including the big tab on the center piece. You’ll notice that two small tabs fold under the center piece — this allows you to glue it to the petals.
Offset the petals, and glue.
Then nestle the center piece in the petals, and the pistil/stamen roll inside that. This is another one where setting it upright to dry is a good idea.
Assemble the leaves and glue to the bottom. You can also slightly roll the petals to make them a little more 3D.
So cute! I’d love to see these on an Easter table in the spring.
Peony
The peony is the most complicated of these four Cricut flowers, but with the knowledge from above you should be able to do it.
The two tiny pistil/stamen pieces aren’t rolled, but are instead just fluffed a bit (can we just talk about what an amazing machine the Cricut Explore is? It cut these perfectly!)
The outer three-petal petals have one tab and are glued like in the daffodil.
The two layers above that have ten petals, which are just curled along the edges a bit to make them 3D. Note that one is slightly bigger than the other — make sure the bigger one is below the smaller one.
Then there are these crazy guys. They actually have six tiny tabs that get glued like this:
A little hard to get the hang of, but once dry and flipped over, you can see how it creates a really nice 3D effect.
Stack all of the petals: the big 3-petal pieces, the 10-petal pieces, then the two smaller pieces in the above photo. You can also put the leaves together as in the flowers above.
Add the pistil/stamen piece and you’ve made a cute peony!
I hope that was helpful for you when you’re building your own Cricut cardstock flowers!
HOW TO MAKE 3D CRICUT CARDSTOCK FLOWERS
Equipment
- Cricut Maker or
Supplies
Instructions
- NOTE: The designs for the following flowers are available in Cricut Design Space individually.Tiger Lily #MA3E15Let's start with the tiger lily. This is a good one to start with because it has a couple features that you'll see over and over in the Cricut flowers. It has three parts — the petals, the pistil/stamen and the leaves.
- You'll see on the petals and the leaves a few small tabs. These tabs are meant to be glued. They will help guide you as you assemble the flower. Many of the cardstock flowers have these tabs, and once you figure out how they work, making flowers becomes a lot easier!Fold the petals of the flowers into sort of a roll. You'll see the tab then overlaps the other side.
- Glue! Do this for both sets of petals and the leaf.
- You'll notice that there are two parts to the leaves, one that is 3D (that you glued) and one that is flat.
- Stack and glue. Sometimes they are made by offsetting them, and sometimes stacked straight on — if making several, try and mix it up a bit.
- For anything that looks like the pistil/stamen, roll it. Use a wooden dowel or pencil to get an even roll. Glue that too.
- To assemble, nestle one set of petals in the other. Glue. Roll the petals a little around a pen to help them spread out.
- Nestle the pistil/stamem inside the petals, and glue. Set it upright in a roll of washi tape to allow it to dry straight. Then glue the leaves to the bottom.Yay! A tiger lily!
- Poppy #MA3E13Let's do the poppy next. There are no tabs on the petals for the poppy, so they stay flat. Roll the edges up a little using a pen, to give them a bit of a 3D feel. Offset the two petal pieces, and glue.
- The pistil/stamen piece may leave you scratching your head, but it's easy. Fold the taller part in half and then roll starting from that side.
- Then glue it to the middle of your poppy.
- Make the leaves like you did the tiger lily, and glue below the petals.
- DaffodilThe daffodil has similar petals to the tiger lily, but it also has that extra piece in the center. Glue all the tabs, including the big tab on the center piece. You'll notice that two small tabs fold under the center piece — this allows you to glue it to the petals.
- Offset the petals, and glue.
- Then nestle the center piece in the petals, and the pistil/stamen roll inside that. This is another one where setting it upright to dry is a good idea.Assemble the leaves and glue to the bottom. You can also slightly roll the petals to make them a little more 3D.
- PeonyThe peony is the most complicated of these four Cricut flowers, but with the knowledge from above you should be able to do it.The two tiny pistil/stamen pieces aren't rolled, but are instead just fluffed a bit.
- The outer three-petal petals have one tab and are glued like in the daffodil.The two layers above that have ten petals, which are just curled along the edges a bit to make them 3D. Note that one is slightly bigger than the other — make sure the bigger one is below the smaller one.Then there are these crazy guys. They actually have six tiny tabs that get glued like this:
- A little hard to get the hang of, but once dry and flipped over, you can see how it creates a really nice 3D effect.Stack all of the petals: the big 3-petal pieces, the 10-petal pieces, then the two smaller pieces in the above photo. You can also put the leaves together as in the flowers above.
- Add the pistil/stamen piece and you've made a cute peony!
Comments & Reviews
Maria Terrazas says
Have you put together the Morning Glory flower from DS?
Angie says
I have an old cricut (expressions) so I cant do internet to get flower patters. Is there a cartridge with these flowers or do you have a pdf version I can cut by hand? Thank you!
Amy Motroni says
Hi Angie,
They were originally part of the Cricut flower cartridge “Cricut Flower Shoppe”
Hope that helps
Amy, HLMS Support
Wendy says
Hi just found this post but not sure how I find the SVG cutting files on these lovely 3D flowers could you let me know please
Thank you for all that you do to make things so much easier to make with your help.
Also a big thank you for all your freebies SVG files such a great help when starting out. Thank you xxx
Nespresso milkshake says
Perfect work you have done, this site is really cool with wonderful info.
maureen says
I could not figure out the poppy assembly – so googled it and your site came up. thank you – i would not have thought to fold the black center in half – the rest was obvious. I did not use the yellow piece either – i think it goes on the backside.
Tre says
I was going nuts trying to figure out my poppy. Thank you! You have truly blessed me.
Meg says
Thank you for the pictures! I wasn’t understanding how to fold and glue that tricky piece with the 6 spokes. I get it now! Thank you!!!!
Cori George says
No problem! They took me a while to figure out when I was first doing them, too! :)
Brandy says
Thank you so much for this!! I have been terrified of making flowers because I just don’t get how to put them together. This made it super easy and understandable!
Cori George says
You’re so welcome!
Jenn says
Thank you for this! I realize you wrote this post a few years ago, but it’s still super helpful.
Cori George says
I’m so glad you found it helpful!
Barb says
I’m trying to make the flowers on page 17 and then look at page 81 I’m guessing looking at it that it looks flat but it’s really not and looks like the front of the box is that right.? Your photo sure helps a lot I was at my wits end how to fix these.
Cori George says
I don’t have the manual, so I’m not sure! I hope my tutorial helped you figure it out :)